Cisco 300-425 Exam Dumps

Cisco 300-425 Sample Question Answers

Question # 1

An engineer must deploy a wireless network in an open-plan environment that has threeSSIDs using the 5 GHz band set to 40 MHz. Co-channel interference must be reduced.Which two actions must be taken? (Choose two.)

A. Increase the number of SSIDs.  
B. Increase channel bonding in the 2.4 GHz band to 40 MHz.  
C. Disable band steering.  
D. Decrease channel bonding in the 5 GHz band to 20 MHz.  
E. Reduce the power of the AP.  

Show Answer

Question # 2

A hospital wireless environment was designed with these characteristics:• RF coverage• better than -67 dBm in the 5 GHz spectrum• RRM be used for DCA and TPC in the 2.4 GHz band• RRM be used for DCA and TPC in the 5 GHz bandAfter deployment, why do many of the legacy 802.11b/g devices have difficulty maintainingconnectivity?

A. Excessive co-channel interference in the 2.4 GHz band exists.  
B. Excessive overlapping channels in the 2.4 GHz band exists.  
C. TPC drastically increases Tx power in the 2.4 GHz band.  
D. TPC drastically reduces Tx power in the 2.4 GHz band.  

Show Answer

Question # 3

A wireless engineer is designing a wireless network for a warehouse using access pointswith internal antennas. Which two elements have a negative effect on the wireless users?(Choose two.)

A. wireless channels  
B. access point height  
C. client authentication  
D. client authorization  
E. absorption  

Show Answer

Question # 4

A Cisco controller-based wireless network must support workgroup bridges. The APscon¬gured as workgroup bridges must support wired and wireless clients. The wirelessclients must connect to the spare radio. What is the maximum number of wired clientconnections supported on a workgroup bridge?

A. 20  
B. 25  
C. 30  
D. 35  

Show Answer

Question # 5

An engineer added an AP to a deployment after a post-installation site survey. Theengineer then notices an increase in co-channel interference and retransmissions. Whichtwo features help mitigate the issue? (Choose two.)

A. Cisco Compatible Extensions  
B. Transmit Power Control  
C. Enhanced Distributed Channel Access  
D. Coverage Hole Detection  
E. Dynamic Channel Assignment  

Show Answer

Question # 6

A customer asks an engineer to explain the concept of mobility domains and mobilitygroups. Which statement does the engineer respond with?

A. A mobility group does not constrain the distribution of security context of a client andalso does not constrain AP fail-over between controllers when the WLC are in the samemobility domain. 
B. If WLCs are in the same mobility domain, they communicate with each other but, if ananchor WLC is present it must be in the same mobility domain for communication to bepossible.
C. If WLCs are in the same mobility domain, they communicate with each other. Mobilitygroups constrain the distribution of security context of a client and also constrain AP failover between controllers. 
D. WLCs do not need to be in the same mobility domain to communicate with each other.Mobility groups constrain the distribution of security context of a client and also constrainAP fail-over between controllers. 

Show Answer

Question # 7

During a meeting to gather the requirements for a new Wi-Fi network design, the customerrequests that to connect. Which affect does this have to the wireless network?

A. bigger channel width  
B. lower throughput  
C. 2.4 GHz signal congestion  
D. higher RF re ection  

Show Answer

Question # 8

An engineer is configuring a centralized set of controllers for separate facilities. Which twoCisco wireless architectures must be used to ensure flexible sizing of WLAN to VLANmappings? (Choose two.)

A. interface group  
B. mobility group  
C. AP group  
D. controller group  
E. RF group  

Show Answer

Question # 9

A customer called with a requirement that internal clients must be on different subnetsdepending on the building they are in. All access points are operating in local mode and willnot be modified, and this is a single controller solution. Which design approach creates thedesired result?

A. Create AP groups for each desired location, map the correct VLANs to the internalSSID, and add the access points for that location.
B. Create an SSID place it to the desired VLAN under WLANs and configure 802.1x in ISEto assign the correct VLAN based on the SSID from which the client is authenticating
C. Create FlexConnect groups, place the access points in, and set the correct VLAN toSSID mapping based on location. 
D. Create mobility anchors for the SSID and on the controller under the internal SSIDcreate a foreign map to the desired VLAN based on location. 

Show Answer

Question # 10

An engineer is setting up the WLC to support a high-density design for a lecture hall. Theengineer must modify the existing high-density RF protocol to obtain a smaller cell size.Also, the clients must connect to the nearest AP using the highest possible data rates.Which setting allows this design?

A. AP load balance  
B. client distribution  
C. power threshold  
D. RX-SOP threshold  

Show Answer